Use these drivers:

ftp://www.siig.com/USB2.0_v2.06.exe

They are generic NEC 2.0 drivers.

Bill

: : 1. Never disable the onboard controller.
: : 2. With onboard enabled, try various slots.

: : Now - I do not see the NEC Enhanced controller. That would be your USB 2.0 controller. You must install that driver through Windows Update or from the manufacturer. If this is Windows 98 (you didn't mention and broke a cardinal forum rule), USB 2.0 is *not supported in Win98*.

: : Update me. ;-)

: : Bill
: : : Hello,
: : : I hope you can help. I recently installed a PCI USB card (Innovision EIO with NEC chip) to my pc which occasionally works fine but mostly hangs the system when accessed. I'm running windows ME on a Shuttle hot 591p, VIA based motherboard. I've updated the bios and tried many different settings, all with the same result. I've tried several clean installations of windows and various combinations of PCI card positions (3 slots- modem, sound & USB)which still proved unsuccesful. Here are my IRQ settings, first with USB disabled in the bios, second enabled.
: : : IRQ 0 System timer OK
: : : IRQ 1 Standard 101/102-Key or Microsoft Natural Keyboard OK
: : : IRQ 2 Programmable interrupt controller OK
: : : IRQ 4 Communications Port (COM1) OK
: : : IRQ 5 IRQ Holder for PCI Steering OK
: : : IRQ 5 NEC USB Open Host Controller (E13+) OK
: : : IRQ 6 Standard Floppy Disk Controller OK
: : : IRQ 7 Printer Port (LPT1) OK
: : : IRQ 8 System CMOS/real time clock OK
: : : IRQ 10 IRQ Holder for PCI Steering OK
: : : IRQ 10 Creative AudioPCI (ES1371,ES1373) (WDM) OK
: : : IRQ 11 IRQ Holder for PCI Steering OK
: : : IRQ 11 WDM Communication Device OK
: : : IRQ 11 EIO USB 2.0 Host Controller OK
: : : IRQ 12 IRQ Holder for PCI Steering OK
: : : IRQ 12 3dfx Voodoo3 OK
: : : IRQ 12 NEC USB Open Host Controller (E13+) OK
: : : IRQ 13 Numeric data processor OK
: : : IRQ 14 VIA Bus Master PCI IDE Controller OK
: : : IRQ 14 Primary IDE controller (dual fifo) OK
: : : IRQ 15 VIA Bus Master PCI IDE Controller OK
: : : IRQ 15 Secondary IDE controller (dual fifo) OK

: : :
: : : IRQ 0 System timer OK
: : : IRQ 1 Standard 101/102-Key or Microsoft Natural Keyboard OK
: : : IRQ 2 Programmable interrupt controller OK
: : : IRQ 3 IRQ Holder for PCI Steering OK
: : : IRQ 3 3dfx Voodoo3 OK
: : : IRQ 3 VIA Tech 3038 PCI to USB Universal Host Controller OK
: : : IRQ 3 NEC USB Open Host Controller (E13+) OK
: : : IRQ 4 Communications Port (COM1) OK
: : : IRQ 5 IRQ Holder for PCI Steering OK
: : : IRQ 5 NEC USB Open Host Controller (E13+) OK
: : : IRQ 6 Standard Floppy Disk Controller OK
: : : IRQ 7 Printer Port (LPT1) OK
: : : IRQ 8 System CMOS/real time clock OK
: : : IRQ 10 IRQ Holder for PCI Steering OK
: : : IRQ 10 WDM Communication Device OK
: : : IRQ 10 EIO USB 2.0 Host Controller OK
: : : IRQ 12 IRQ Holder for PCI Steering OK
: : : IRQ 12 Creative AudioPCI (ES1371,ES1373) (WDM) OK
: : : IRQ 13 Numeric data processor OK
: : : IRQ 14 VIA Bus Master PCI IDE Controller OK
: : : IRQ 14 Primary IDE controller (dual fifo) OK
: : : IRQ 15 VIA Bus Master PCI IDE Controller OK
: : : IRQ 15 Secondary IDE controller (dual fifo) OK

: : : P.S I've tried it without the sound card and modem installed but still no good. Sorry for so much info but thanks in anticipation.

:
: I'm running Windows ME. The disk that came with the card was empty on arrival so I downloaded what I thought were the latest drivers from their website (Innovisions). Do you think I should visit NEC's website for the drivers? Windows update said no recommended device drivers at this time. Thanks again